|
|
Order by: |
0 bids $6.99 Shipping
Condition: New Location: Sunnyvale, United States
Square drive 1/2" drive x 1.187" flats, this will fit all of your 50 taper retention knobs. You can also open it by 30 mm wrench. Made of high grade tool steel S7 and heat treating (harden 60 Rc).
0 bids Free Shipping
Condition: Used Location: Dayton, United States
SOLD BY M & J TOOLING LLC. TOOL HOLDER RETENTION KNOBS / PULL STUDS. M & J TOOLING LLC. Thread Gages. Top Quality Products. 5/8 11 THREADS. YOU ARE PURCHASING THE 10 PICTURED. ”Gage was protected very good.
0 bids Free Shipping
Condition: New Location: Walnut, United States
SFX 10 Pcs BT40 45° Pull Stud Retention Knob Coolant Thru Fit BT40 Tool Holders. Each pull stud is tested thoroughly which ensures the quality of the pull stud. Processing thread after carburizing and quenching makes thread accurate.
0 bids $6.00 Shipping
Condition: New Location: Irvine, United States
MODEL BT40 HEAD D1 0.59 OVER LENGTH L 2.36. The facility with ISO9000 in 2007approved. THREAD M16 X2 POLIT D3 0.669 SHOULDER l1 1.37. Send Check to 192 technology dr. Site P Irvine CA92618.
Buy It Now
Free Shipping
Condition: New Location: South El Monte, United States
Fits Kira, Milltronic, Hitachi-Seiki, Mitsubishi, Okuma, Matsura, Howa Kogyo. 10 x CAT 40 5/8-11 60° Pull Stud.
Buy It Now
$8.00 Shipping
Condition: New Location: Saint Charles, United States
TEGARA CAT40 PULL STUD RETENTION KNOB FITS ANY HAAS TOSHIBA. underneath the flange area. Taper: CAT 40. holder's taper end and retention knob. CAT 40 CNC NEW. next to the threads which will reduce the vibrationand minimize TIR on the overall system (tools holder + retention. ).
Buy It Now
Free Shipping
Condition: New Location: Seminole, United States
T.J. Davies’ retention knobs are the highest quality retention knobs on the market. For over 50 years, we have been second to none. The retention knob or pull stud is a critical component to the tool holder’s performance and cutting tool life.
Buy It Now
Free Shipping
Condition: New Location: Tracy, United States
Retention knob will fit on most of mazak cnc cat40 except VQC 20/40. Can be used on both spindle coolant through and non-coolant through MAZAK and FADAL. On FADAL, will fit on most of VMC models. Taper: CAT 40.
Buy It Now
Free Shipping
Condition: New Location: South El Monte, United States
10 x CAT40 90° Pull Stud. Fits Mori Seiki, Kia. The fitting accuracy is obviously higher than that of machine pull stubs, effectively reduces the error of machine tool and cooperation, so as to improve the accuracy and stability of the connection and improves the precision of the machine tools and lengthens the service life.
0 bids $5.00 Shipping
Condition: New Location: Huntington Beach, United States
Coolant-I 45-degree retention knob / pull stud,1.266" gage length. Manufactured to the highest standards for maximum safety and long life. All mating surfaces precision ground. Our part # TEC-21003-45C.
Buy It Now
$8.00 Shipping
Condition: New Location: Commack, United States
The part number and instructions inside are JM Performance Products (JMP) but the label says Trinity Mill. In general, I have cleaned the item very lightly for any bulk surface dust, dirt, etc. I have NOT deep cleaned it and will not be doing so here.
0 bids Free Shipping
Condition: New Location: Chino, United States
Product description Condition:100% Brand New & High Quality Fitment For Hass Kia Toshiba Taper: BT 40 A: 45 D1 Knob: 0.589" D2 Neck: 0.392" D3 Hole: N/A D4 Pilot: 0.669" L: 2.360" L1: 1.100" L2 Shou to End: 1.376" Knob Socket: RKW40 Package Include: 10x BT40 Pull Stud Brand autoooparts MPN APO78048 UPC Does not apply.
Buy It Now
Free Shipping
Condition: New Location: Naperville, United States
For Taper Cat 60. Thread Size 1.250-7.
0 bids Free Shipping
Condition: New Location: Chino, United States
Specification: Taper: CAT 40 A: 45° D1 Knob: 0.589" D2 Neck: 0.392" D3 Hole: N/A D4 Pilot: 0.6360" L: 2.250" L1: 0.988" L2 Shou to End: 1.264" Knob Socket: RKW40 Description: High quality and durable. Good working conditions and easy installation. Sufficient warranty time and good after-sales service. Please rest assured to buy products from our shop. Key Features: Condition:100% Brand New & High Quality. For HAAS TOSHIBA. Package List: 10× CAT40 Pull Stud .
0 bids Free Shipping
Condition: New Location: Monroe Township, United States
Description: Condition:100% Brand New & High Quality Fitment For Hurco Mazak Okuma Fadal Product description: ANSI Standard Taper: CAT 40 C: 45 D1 Knob: 0.740" D2 Neck: 0.490" D3 Hole: 0.28" D4 Pilot: 0.636" L: 1.625" L1: 0.440" L2 Shou to End: 0.640" Knob Socket: RKW40 Package Include: 10x CAT 40 Pull Stud Brand ALL-CARB MPN Does Not Apply Warranty 1 year UPC Does not apply Type Pull Stud Custom Bundle No Modified Item No Modification Description No.
0 bids Free Shipping
Condition: New Location: Monroe Township, United States
Condition:100% Brand New & High Quality Fitment For Mazak Head Diameter D1: 1.14 Head Angle: 45 Drawbar Thread Size: 1-8unc Machine Taper Size: CAT50 Machine Builder: Mazak Neck Diameter d2: 0.82 Hole d3: 0.39 Pilot d4: 1.026 Overall Length L: 2.3 Shoulder To Head L1: 0.7 Shoulder To End L2: 1 Coolant Hole: Yes Package Include: 100x CAT 50 Pull Stud Brand labwork MPN LAW58518 UPC Does not apply.
Buy It Now
Free Shipping
Condition: New Location: Madison Heights, United States
DESCRIPTION: "CNC Tooling" Brands---The Best Quality on The Market---Sold Many Thousands to Distributors!*This set including: 10 PCS CAT40 CNC TOOLING RETENTION KNOBS PS-532X45 FITTING MACHINES OF HASS, KITAMURU, OKUMA, MILTRONICS BRANDS. Coolant Tru style5/8"-11 thread.Large Inventory! Same Day Shipping!Froo www.froo.com | Froo Cross Sell, Free Cross Sell, Cross promote, eBay Marketing, eBay listing Apps, eBay Apps, eBay Application
0 bids Free Shipping
Condition: Used Location: Newberg, United States
Do not attempt to make repairs or have the item repaired. We will not accommodate requests to work around or outside their policies.
Buy It Now
Free Shipping
Condition: New Location: Saint Charles, United States
FitsKira, Milltronic, Hitachi-Seiki, Mitsubishi, Okuma, Matsura, Howa Kogyo. Shars tools are manufactured by anISO 9001 certified manufacturer with 60 plus years of hands-on experience inthe CNC machining industry.
Buy It Now
Free Shipping
Condition: New Location: Saint Charles, United States
SHARS 10 PCS CAT40 PULL STUD RETENTION KNOB FITS MAZAK. Shars tools are manufactured by anISO 9001 certified manufacturer with 60 plus years of hands-on experience in the CNC machining industry. & Mazak Other studs will be slightly higher.
0 bids Free Shipping
Condition: New Location: Monroe Township, United States
Feature： Condition:100% Brand New & High Quality Fitment For HAAS TOSHIBA Taper: CAT 40 A: 45° D1 Knob: 0.589" D2 Neck: 0.392" D3 Hole: N/A D4 Pilot: 0.6360" L: 2.250" L1: 0.988" L2 Shou to End: 1.264" Knob Socket: RKW40 Description： The product has passed strict quality testing Durable and easy to install and replace Cost-effective, good after-sales service Quality assurance for your peace of mind Package List: 10 PCS CAT40 Pull Stud Notes: Pls check your old picture or model when you order it..
Buy It Now
Free Shipping
Condition: New Location: Saint Charles, United States
Shars tools are manufactured by anISO 9001 certified manufacturer with 60 plus years of hands-on experience inthe CNC machining industry. The fitting accuracy is obviously higher than that of machine pull stubs, effectively reduces the error of machine tool and cooperation, so as to improve the accuracy and stability of the connection and improves the precision of the machine tools and lengthens the service life.
0 bids Free Shipping
Condition: New Location: Los Angeles, United States
10Pcs CAT40 15° 0.747" Pull Stud Coolant Thru Retention Knob For DMG Mori. Machine Taper Size: CAT40. MACHINE BUILDER DMG Mori, Doosan, Feeler, Mori Seiki. COOLANT HOLE. This pull stud is fit for the following.
0 bids Free Shipping
Condition: Used Location: Dayton, United States
Type & Size : CAT40 MAS1 45-Degree w/ 5/8-11 threads.
Buy It Now
Free Shipping
Condition: New Location: Saint Charles, United States
Tegara CAT 40 5/8-11 90 Pull Stud Retention Knob Fits Mori Seiki CNC New. Machine Taper Size CAT40. Machine Builder Mori Seiki. The ultimate tensile strength of SNCM420 alloy steel is 980 MPa and our material is made in Japan by a very reputable steel manufacturer.
0 bids Free Shipping
Condition: New Location: Troy, United States
BT30 PULL STUDS. DURING THE WORK WEEK.
Buy It Now
Free Shipping
Condition: New Location: South El Monte, United States
Can be used on both spindle coolant through and non-coolant through HAAS CAT40 V mill. Fits on any HAAS V mill, like VF, mini mill, EC, ES, etc. Taper: CAT 40. D1 Knob: 0.589". 10 x CAT 40 Pull Stud.
Buy It Now
Free Shipping
Condition: New Location: Saint Charles, United States
Tegara Pull Stud Retention Knob FITS Mazak Fadal Hurco Okuma. Fits on Hurco,Mazak, Okuma,Fadal. & Mazak Other studs will be slightly higher. Also available is a CAT40 CNC Tool Tightening Fixture. underneath the flange area.
0 bids $29.00 Shipping
Condition: New Location: Irvine, United States
For all BT40. Send Check to 192 technology dr. Site P Irvine CA92618.
0 bids $3.00 Shipping
Condition: New Location: Saint Louis, United States
We are happy to help.
0 bids $3.00 Shipping
Condition: New Location: Saint Louis, United States
Credit Card or Debit Card.
Buy It Now
Free Shipping
Condition: New Location: Walnut, United States
10PCS CAT40 Pull Stud Retention Knob 461U/T Coolant Thru Fit HAAS CAT40 CNC. Each pull stud is tested thoroughly which ensures the quality of the pull stud. Processing thread after carburizing and quenching makes thread accurate.
Buy It Now
$4.99 Shipping
Condition: Used Location: Fort Lauderdale, United States
Lot of 5 pcs BT40 Coolant Thru Tool Holder Retention Knobs Pull Stud COMMAND M16.
Buy It Now
Free Shipping
Condition: New Location: South El Monte, United States
Thread: M16. Machine Taper: BT40 non hole thru. Machine Taper: BT40. Suitable for machining center, CNC knife handle, connecting, fasteners. MAS specification pull-head screws with BT standard shank. 10 x BT40 Pull Stud.
0 bids $7.99 Shipping
Condition: New Location: Clinton Township, United States
0 bids Free Shipping
Condition: New Location: Chino, United States
Description： Head Diameter：0.747" Head Angle ： 75° Drawbar Thread Size：5/8"-11 Machine Taper Size ：CAT40 Neck Diameter：0.549" Hole：0.281" Pilot：0.641" Overall Length：2.001" Shoulder To Head：0.787" Shoulder To End：1.024" Coolant Hole Features： Made from alloy steel 5155 with heat treat to RC 56-58 Each retention knob is individually magnetic particle tested to ensure free of crack High quality black oxide finish to ensure long enduring tool life.
0 bids Free Shipping
Condition: Used Location: Waterford, United States
USED FITZ RITE CAT50( 50RK-138-45C ) THRU TOOL COOLANT RETENTION KNOBS.PRICE IS PER LOT OF 5PCS.
Buy It Now
Free Shipping
Condition: New Location: Schaumburg, United States
10PC Quality Pull Stud / Retention Knob Fits on any HAAS CAT40 CNC V Mill. Can be used on both spindle coolant through and non-coolant through HAAS CAT40 V mill. Fits on any HAAS V mill, like VF, mini mill, EC, ES, etc.
0 bids Free Shipping
Condition: New Location: Monroe Township, United States
Key Features: Made from alloy steel 5155 with heat treat to RC 56-58. Each retention knob is individually magnetic particle tested to ensure free of crack. High quality black oxide finish to ensure long enduring tool life. Fully ground on all critical surface including a pilot under the flange of retention knob for full contact between tool holder's taper end and retention knob. Fitment For Mazak. 100% Brand New & High Quality. Head Diameter D1: 1.14 Head Angle: 45 Drawbar Thread Size: 1-8unc Machine Taper Size: CAT50 Machine Builder: Mazak Neck Diameter d2: 0.82 Hole d3: 0.39 Pilot d4: 1.026 Overall Length L: 2.3.
0 bids Free Shipping
Condition: New Location: Monroe Township, United States
Specification： For Kira Okuma Roku-Roku Taper: BT 40 A: 60 D1 Knob: 0.589" D2 Neck: 0.392" D3 Hole: N/A D4 Pilot: 0.669" L: 2.360" L1: 1.100" L2 Shou to End: 1.376" Knob Socket: RKW40 Package Include: 10x BT40 Pull Stud Description: Highest After-Sales Guarantee Low Cost,Highest Cost Performance Brand New & High Quality Durable And Easy To Install Note： If You Are Uncertain About The Item, Please Feel Free To Contact Us For Confirm. Sorry For Any Inconvenience Caused..
0 bids $3.99 Shipping
Condition: New Location: Sunnyvale, United States
RETENTION KNOB SOCKET FITS ALL 30 TAPER (CAT30, BT30) PULL STUD. * Square drive 3/8" drive x 3/4" flats, this will fit all of your 30 taper retention knobs. *You can also open it with a 7/8 inch wrench. * Made of high-grade tool steel S7 and heat treating (harden 60 Rc). *100% Satisfaction Guaranteed. * One year warranty, free return shipping cost. We also make custom tools and parts. Contact us for the special wholesale/ custom prices. Sunnyvale CNC, INC 3737 Yale WayFremont, CA 94538 website: sunnyvalecnc.comTel (408) 480 2453 (408) 702 0294Thank you for looking!
0 bids Free Shipping
Condition: New Location: South El Monte, United States
The fitting accuracy is obviously higher than that of machine pull stubs, effectively reduces the error of machine tool and cooperation, so as to improve the accuracy and stability of the connection and improves the precision of the machine tools and lengthens the service life.
Buy It Now
Free Shipping
Condition: New Location: Chino, United States
AIR, POWER & HAND TOOLS. Why should you buy from us?. The thread is M16 X 2.0. L2 is. 16". L1 is. 79". L is 2.13". D4 is. 67". D3 is. 28".
Buy It Now
Free Shipping
Condition: New Location: Saint Charles, United States
MACHINE BUILDER Doosan, Feeler. MACHINE TAPER SIZE BT40. COOLANT HOLEYes. quality Pull Stud. This pull stud is compatible with the following DRAWBAR THREAD SIZE M16x2.0. HOLE D30.2775. HEAD ANGLE 15.
Buy It Now
Free Shipping
Condition: New Location: South El Monte, United States
Taper: CAT 40. D1 Knob: 0.740". Knob Socket: RKW40. L2 Shou to End: 0.640". Size: As Picture.
0 bids Free Shipping
Condition: New Location: Paola, United States
CAT40, 5/8-11 Thread, 45 ° Angle Radius, 0.74″ Knob Dia. Taper Size CAT40. Through Coolant Yes.
Buy It Now
Free Shipping
Condition: New Location: South El Monte, United States
Machine Taper Size: CAT40. MACHINE BUILDER DMG Mori, Doosan, Feeler, Mori Seiki. 10 x CAT40 Pull Stud. The fitting accuracy is obviously higher than that of machine pull stubs, effectively reduces the error of machine tool and cooperation, so as to improve the accuracy and stability of the connection and improves the precision of the machine tools and lengthens the service life.
0 bids Free Shipping
Condition: New Location: Monroe Township, United States
Description： Head Diameter：0.747" Head Angle ： 75° Drawbar Thread Size：5/8"-11 Machine Taper Size ：CAT40 Neck Diameter：0.549" Hole：0.281" Pilot：0.641" Overall Length：2.001" Shoulder To Head：0.787" Shoulder To End：1.024" Coolant Hole Features： Made from alloy steel 5155 with heat treat to RC 56-58 Each retention knob is individually magnetic particle tested to ensure free of crack High quality black oxide finish to ensure long enduring tool life.
0 bids Free Shipping
Condition: Used Location: Waterford, United States
A USED SET OF HPI CAT40 RETENTION KNOBS LOT OF 5 PCS.
Buy It Now
Free Shipping
Condition: New Location: Madison Heights, United States
DESCRIPTION: "CNC Tooling" Brands---The Best Quality on The Market---Sold Many Thousands to Distributors!*This set including: 10 PCS CAT40 CNC TOOLING RETENTION KNOBS PS-532X45 FITTING MACHINES OF HASS, KITAMURU, OKUMA, MILTRONICS BRANDS. 10 PCS total price: $38.00 free shipping.5/8"-11 thread.Solid bodyLarge Inventory! Same Day Shipping!Froo www.froo.com | Froo Cross Sell, Free Cross Sell, Cross promote, eBay Marketing, eBay listing Apps, eBay Apps, eBay Application
Buy It Now
Free Shipping
Condition: New Location: South El Monte, United States
Fits on Hurco Mazak Okuma Fadal. The fitting accuracy is obviously higher than that of machine pull stubs, effectively reduces the error of machine tool and cooperation, so as to improve the accuracy and stability of the connection and improves the precision of the machine tools and lengthens the service life.
Buy It Now
Free Shipping
Condition: New Location: Madison Heights, United States
This set including.
Buy It Now
Free Shipping
Condition: Used Location: Katy, United States
Loc. VID-F2Pre owned/used item. In overall good to very good condition. Purchase is for (1) unit. Multiple units available.We ship out same day if paid by 2pm central. Sells and ships from Houston TX.☀️CAT50 Pull Stud Retention Knob, Coolant Through, 1.00-8 UNC 45° Degree. Thread Size: 1.00-8Angle: 45°Head Diameter: 1.140Neck Diameter : 0.820Hole (Diameter): Yes (0.468)L1: 0.700L2: 1.000O-Rings: No
Buy It Now
$6.50 Shipping
Condition: Used Location: Madison, United States
🗽CAT 40 RETENTION KNOBS one is coolant through. 3pieces (B25-50)
Buy It Now
Free Shipping
Condition: New Location: South El Monte, United States
M16 BT40 x 45 Degree Pull Stud Retention Knob For CNC Milling Tool Holder. 5pcs BT40 M16 90 Degree Pull Stud Retention Knob Fits Kia Mori Seiki BT40. 5 High Quality BT40 Pull Stud Retention Knob CNC Milling M16 45 Degrees.
Buy It Now
Free Shipping
Condition: New Location: South El Monte, United States
Machine Taper: BT30 non hole thru. Machine Taper: BT30. MAS specification pull-head screws with BT standard shank. Angle Degree: 45 degrees. Thread: M12. Have sufficient tensile strength. Hard wear-resistant surface.
Buy It Now
$6.92 Shipping
Condition: New Location: Columbia, United States
ACCUPRO MPN: #88.600.30AP MSC PART NUMBER: 55833487 MADE IN GERMANY.
0 bids Free Shipping
Condition: New Location: South El Monte, United States
Fits Kira, Milltronic, Hitachi-Seiki, Mitsubishi, Okuma, Matsura, Howa Kogyo. 10 x CAT 40 5/8-11 60° Pull Stud.
0 bids $4.40 Shipping
Condition: New Location: East Jordan, United States
DIN 69872, FORM A. Erickson CAT40 Retention Knob. Part #RK40DVM.
Buy It Now
Free Shipping
Condition: Used Location: Campbellsport, United States
4 - JM71145HTHS High Torque© High Strength retention knob, CAT 50, 1"-8; 15°. They are $75 each new.
|
|
|
|